網站公告:

新聞中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區西周南路9號

網址:http://www.transgenx.com

常見問題

當前位置:首頁 - 新聞中心 - 常見問題 - 氣液增壓泵在更換密封件時

氣液增壓泵在更換密封件時需要怎樣操作?

發布時間:2022-03-04 20:53:10   發布人:http://www.transgenx.com
一、由人員對氣液增壓缸更換密封件
1、 The sealing parts of the gas-liquid booster cylinder shall be replaced by professionals
氣液增壓泵這種結構簡單緊湊的產品,裝配起來并不是很難,但是需要經過相關的培訓,否則很容易因為裝配的原因導致產品不能正常動作。此類產品主要由氣缸筒、儲油筒、油缸、活賽、密封件等組成。其中,密封圈有幾十個不同規格尺寸的,分別用于活塞上、中間蓋上、活塞上、前蓋上等等,安裝時要注意轉配細節,否則容易損壞密封件。建議由人員來更換,或聯系氣液增壓缸廠家更換。
The gas-liquid booster pump, a product with simple and compact structure, is not very difficult to assemble, but it needs relevant training. Otherwise, it is easy for the product to fail to operate normally due to assembly. Such products are mainly composed of cylinder, oil reservoir, oil cylinder, movable race, seal, etc. Among them, there are dozens of sealing rings with different specifications and sizes, which are used on the piston, the middle cover, the piston, the front cover, etc. pay attention to the matching details during installation, otherwise it is easy to damage the seals. It is recommended to replace it by professionals or contact the manufacturer of gas-liquid booster cylinder.
二、氣液增壓泵更換密封件前的注意事項
2、 Precautions before replacing seals of gas-liquid booster pump
氣液增壓泵
1、檢查前軸。
1. Check the front axle.
在安裝油封之前,先檢者前軸表面是否過于相糙,有無嚴重的碰壞痘跡。由于氣藥增床缸長時間,作而導致的軸向的長拉傷。如里軸表面過干粗精不光滑,就會揭壞油封影響容封性能,若軸表面有析裝不當而造成嚴重的拉傷,會使油封展目與軸表面貼合有縫,會導致油液滲漏,如果有這樣的情況,建議更換新軸,因為軸表面必須要具有較高的光潔度
Before installing the oil seal, first check whether the front axle surface is too rough and whether there are serious bumps. Long axial strain caused by long-time operation of gas propellant bed increasing cylinder. If the surface of the inner shaft is too dry, rough and smooth, it will damage the oil seal and affect the sealing performance. If the shaft surface is badly strained due to improper disassembly and assembly, it will make the oil seal fit closely with the shaft surface and lead to oil leakage. If so, it is recommended to replace the shaft, because the shaft surface must have a high finish
2、檢查軸頭。
2. Check the shaft head.
對于簡單的軸頭只有金屬手刺或邊,就可用鏗力修磨平整,防止安裝油封時劃傷油封唇目,再檢音油封質量是否展目有無破缺、傷裂或油化腐蝕,如發現這些不良現象,就不能使用必須更換新油封。
For a simple shaft head with only metal thorns or edges, it can be polished with Keng force to prevent scratching the lip and eye of the oil seal when installing the oil seal, and then check whether the quality of the oil seal is expanded, whether there is damage, crack or oily corrosion. If these adverse phenomena are found, it can not be used, and the oil seal must be replaced.
新聞推薦:
氣體增壓泵可以為工廠帶來哪些優勢? 2022-03-17
氣液增壓泵在更換密封件時需要怎樣操作? 2022-03-04
氣體增壓泵的保養與維護該怎么做? 2022-02-25
液壓安全閥校核試驗臺是以什么參數出場的? 2022-02-10
氣動液壓泵的工作原理及介紹 2022-01-24
氣液增壓泵如何增加壓力工作? 2022-01-11
新買的增壓泵為啥呢么需要一直加壓? 2021-12-30
氣體增壓泵是如何保證自己的生產進度的? 2021-12-16
氣體增壓泵在工廠使用要注意哪些優勢? 2021-12-09
氣體增壓泵空氣增壓泵可以使用多長時間? 2021-11-30

13188935873

qq

国产人久久人人人人爽-李老汉吃嫩草开花苞小雪-亚洲va欧洲va日韩va忘忧草-gogo全球高清大胆摄影专业网